cckla,
My understanding is that when a high load is placed on the ground that
load is dissipated into the ground in the shape of a cone. Just under the
load the pressure is high but deeper in the ground the load has spread out
over a greater area so the pressure is lower. If you go deep enough the
pressure under the load will in fact reduce to close on zero because the
load is spread over such a wide area. Dropping the pipe to a lower level
in the ground will place it in an area where the pressure from traffic
passing overhead will be lower. I agree with you the soil load will be
greater. I suppose the object of the exercise is to find that depth where
the total effect, (traffic load + soil load are a minimum).
I once attended a course on pipelines which discussed water pipes in great
detail and those formulas you are talking about were undoubtedly
explained. I do not have that material with me at work so you will have
to wait until tomorrow before I can comment on those formulas.
What I can tell you however is that those formulas apply to large diameter
water pipes made of concrete, plastic and fairly weak materials. The
pressure in those lines is low. If you are dealing with steel pipes with
diameters like 300mm and wall thickness like schedule 40 the soil loads
are of no consequence at normal burial depths and are rarely if ever
calculated.
You would put in a thicker pipe to increase the strength under a road
crossing, not a larger diameter. The load traffic load will attempt to
compress the pipe and make it collapse inwards. The larger the diameter,
the weaker the pipe will be from that point of view.
I will scavenge for the course notes I have on those formulas and come
back to you tomorrow.
Gordon Reddek
Specialist Mechanical Engineer
Alcan Engineering, Level 3, 443 Queen St, Brisbane, Qld 4001, Australia.
Tel: +61 7 3328 6424
Fax: +61 7 3328 6990
Email: <a href="/group/PipingDesign/post?postID=WZ8x3dJsOAcT1GG219G7de1z09ASIc1pn9zbnx7ofDcqrIr7DTeaKWJGdZZxXydCiJK0T3U2RIhIt7fFRFPoBew">gordon.reddek@alcan.com</a>
"cckla" <cckla@pd.jaring.my>
07/06/2004 03:38 PM
Please respond to
<a href="/group/PipingDesign/post?postID=-y7EpnqG4iZl7m4wss_O1RBugEY2OxBUvqwJaRKEcVqvRj2cArs8-J4bLC35nPUGwHXWBiYSJKEUJaEvaVJdqNJZ">PipingDesign@yahoogroups.com</a>
To
<PipingDesign@yahoogroups.com>
cc
Subject
Re: [PipingDesign] Underground Piping
Dear Gordon Reddek,
My job are not only deal with fire fighting but I also involve in water supply system. In this case, I am in the position of dealing with water supply.
From your previous reply,
> 2) If the road is to be subject to abnormal traffic, like trucks
> carrying heavy equipment, one normally buries the pipe deeper
In my opinion, if the pipe was buries deeper, the buried laod on that pipe will be increased. Is it a normal practice to use larger diameter pipe ? Or there are some rules to be followed during the selection of the pipe ?
Do you know what is the difference in the usage of the formula CWB2 and CWD2 in calculating the dead buried load for underground piping ? Where C = coefficient and 2 indicate power of 2.
W = soil weight
B = trench width
D = pipe diameter
There are two ways of calculating the dead buried load. So, I believe that
there must be difference during the installing of the underground pipe.
Can you let me know the difference ?
Please guide me.
Thanks.
cckla
cckla,
I doubt it very much. I have never found a useful free standard on the web. The majority of those organisations are now private organisations bent on making a profit, so you can expect to pay. It looks as though you
are designing a fire water system. I suggest you surf the national fire
protection association (nfpa) website and look at the short descriptions
they give for each standard and take a punt on the ones that may cover the
subject of buried line. Once you know what you are looking for see if you
cant loan a copy from your national library or technical institution. I
did a quick google search and found the following site which you could
start with.
<a href="http://www.nfpa.org/catalog/home/index.asp?cookie%5Ftest=1">http://www.nfpa.org/catalog/home/index.asp?cookie%5Ftest=1</a>
Cheers,
Gordon Reddek
Gordon Reddek
Specialist Mechanical Engineer
Alcan Engineering, Level 3, 443 Queen St, Brisbane, Qld 4001, Australia.
Tel: +61 7 3328 6424
Fax: +61 7 3328 6990
Email: <a href="/group/PipingDesign/post?postID=WZ8x3dJsOAcT1GG219G7de1z09ASIc1pn9zbnx7ofDcqrIr7DTeaKWJGdZZxXydCiJK0T3U2RIhIt7fFRFPoBew">gordon.reddek@alcan.com</a>
"cckla" <cckla@pd.jaring.my>
03/06/2004 06:24 PM
Please respond to
<a href="/group/PipingDesign/post?postID=-y7EpnqG4iZl7m4wss_O1RBugEY2OxBUvqwJaRKEcVqvRj2cArs8-J4bLC35nPUGwHXWBiYSJKEUJaEvaVJdqNJZ">PipingDesign@yahoogroups.com</a>
To
<PipingDesign@yahoogroups.com>
cc
Subject
Re: [PipingDesign] Underground Piping
Dear Mr. Gordon Reddek,
Thank you for your informations. Anyway, is there any international piping
codes which are available online, such as nfpa for fire services ?
Regards,
cckla
Dear Thanks,
The criteria for buried pipe depends on the code that has jurisdiction
over the facility you are designing. These days one seldom designs a
pipeline from first principles, you have to design to the requirements
of
either a national, or international standard. As always you guys
give
insufficient information to give good advice. What are we talking
about
here. High pressure steel oil or gas line, plastic or a concrete sewer?
What is the diameter? two inches or six feet? For what it is worth:
1) Steel high pressure oil and gas lines under roads with normal
traffic
are normally buried with 1200mm cover, that means from the top of the pipe
to the road surface.
2) If the road is to be subject to abnormal traffic, like trucks
carrying
heavy equipment, one normally buries the pipe deeper, or , the pipe
runs
in a culvert designed by civil engineers to take the load, or a slab is
cast over the pipe to distribute the load to the ground on both sides of
the pipe.
3) Very large diameter low pressure lines like sewers require special
treatment. That is the area of a specialist and you should not touch
it
if you are not qualified.
Regarding bedding material. The soil below the pipe is commonly called
bedding and that above the line is called shading. Normally it has to
surround the pipe with a layer of at least six inches (or 150mm). The
specification normally calls for clean loose sand free of stones and
extraneous material. Some specs may even nominate a sieve size that
the
sand must pass through however it is not uncommon to see clauses like
"the
sand may contain stones of a rounded shape and with a diameter no
greater
than (say) 10mm." The details will depend on the pipe coating. If
the
pipe is a steel pipe coated with a fairly soft coating the spec will have
to be stringent to protect the coating from damage by the bedding and
shading material. If the pipe is a concrete monster you would most
probably call for a loose sand bedding so that the pipe can be
levelled
properly and shading with the excavated material provided the lump
size
is on average no greater than (say) 100mm. What you specify depends
on
the pipe you are installing.
Sure you can join pipe under roads. If you are running gas or some
other
dangerous material you will not want a leak there so one tends to be
more
stringent regarding joints in that area. Some Authorities may require
that the line under a road is jointless, however in general pipe codes
require the pipe in that sort of area to be thicker so that they are
more
lightly stressed. Flanges are generally not allowed on buried
installations so I would expect that a full penetration butt weld
which
is
subject to 100% NDT would be considered to be acceptable.
Once again, you must find out what code governs the way you design your
line and you must be guided by the requirements of that code.
Gordon Reddek
Specialist Mechanical Engineer
Alcan Engineering, Level 3, 443 Queen St, Brisbane, Qld 4001,
Australia.
Tel: +61 7 3328 6424
Fax: +61 7 3328 6990
Email: <a href="/group/PipingDesign/post?postID=WZ8x3dJsOAcT1GG219G7de1z09ASIc1pn9zbnx7ofDcqrIr7DTeaKWJGdZZxXydCiJK0T3U2RIhIt7fFRFPoBew">gordon.reddek@alcan.com</a>
"cckla" <cckla@pd.jaring.my>
02/06/2004 03:40 PM
Please respond to
<a href="/group/PipingDesign/post?postID=-y7EpnqG4iZl7m4wss_O1RBugEY2OxBUvqwJaRKEcVqvRj2cArs8-J4bLC35nPUGwHXWBiYSJKEUJaEvaVJdqNJZ">PipingDesign@yahoogroups.com</a>
To
<PipingDesign@yahoogroups.com>
cc
Subject
[PipingDesign] Underground Piping
Dear All Specialists,
1) What are the criterias, which determine the depth of the
underground
pipe ?
2) What should be considered in the selection of soil for the
underground pipe trench ?
3) Should there be any joint under the crossing road ? If yes,
what
will be the suitable joints ?
Thanks
[Non-text portions of this message have been removed]
=========================================
PipingOffice - Excel Spreadsheets for Piping Calculations
<a href="http://www.pipingoffice.us/">http://www.pipingoffice.us/</a>
=========================================
Main site: <a href="http://www.pipingdesign.com">http://www.pipingdesign.com</a>
Yahoo! Groups Links
Notice:
This message and any attachments are the property of Alcan and are
intended solely for the named recipients or entity to whom this
message
is
addressed. If you have received this message in error please inform
the
sender via e-mail and destroy the message. If you are not the intended
recipient you are not allowed to use, copy or disclose the contents or
attachments in whole or in part.
[Non-text portions of this message have been removed]
PipingOffice - Excel Spreadsheets for Piping Calculations
<a href="http://www.pipingoffice.us/">http://www.pipingoffice.us/</a>
=========================================
Main site: <a href="http://www.pipingdesign.com">http://www.pipingdesign.com</a>
Yahoo! Groups Sponsor
ADVERTISEMENT
------------------------------------------------------------------------------
Yahoo! Groups Links
a.. To visit your group on the web, go to:
<a href="http://groups.yahoo.com/group/PipingDesign/">http://groups.yahoo.com/group/PipingDesign/</a>
b.. To unsubscribe from this group, send an email to:
<a href="/group/PipingDesign/post?postID=63RcGsN_TbzU5amn53-VP5Q3G4-RMDkHTaMxbKJFSxToTLuv0cuJSOPczRjkQI2Be_El-qSiD0TJrPxEfsTa9-xc2o5ihN0ibhtkXshM">PipingDesign-unsubscribe@yahoogroups.com</a>
c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service.
[Non-text portions of this message have been removed]
Yahoo! Groups Links
Notice:
This message and any attachments are the property of Alcan and are
intended solely for the named recipients or entity to whom this message
is
addressed. If you have received this message in error please inform the sender via e-mail and destroy the message. If you are not the intended recipient you are not allowed to use, copy or disclose the contents or attachments in whole or in part.
[Non-text portions of this message have been removed]
Yahoo! Groups Sponsor
ADVERTISEMENT
------------------------------------------------------------------------------
Yahoo! Groups Links
a.. To visit your group on the web, go to:
<a href="http://groups.yahoo.com/group/PipingDesign/">http://groups.yahoo.com/group/PipingDesign/</a>
b.. To unsubscribe from this group, send an email to:
<a href="/group/PipingDesign/post?postID=63RcGsN_TbzU5amn53-VP5Q3G4-RMDkHTaMxbKJFSxToTLuv0cuJSOPczRjkQI2Be_El-qSiD0TJrPxEfsTa9-xc2o5ihN0ibhtkXshM">PipingDesign-unsubscribe@yahoogroups.com</a>
c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service.
[Non-text portions of this message have been removed]
Yahoo! Groups Links
Notice:
This message and any attachments are the property of Alcan and are
intended solely for the named recipients or entity to whom this message is
addressed. If you have received this message in error please inform the
sender via e-mail and destroy the message. If you are not the intended
recipient you are not allowed to use, copy or disclose the contents or
attachments in whole or in part.
[Non-text portions of this message have been removed] Received on Mon Jun 07 20:52:00 2004
This archive was generated by hypermail 2.1.8 : Tue Mar 04 2008 - 11:40:34 EST