Deepak
Refer "Piping Design and Engineering" by Grinnel or
"Design of Piping Systems" by Kellog(recommended by
Steve earlier). Piping book from Tube turns also is a
good reference.
Cheers
HVR
- GET Mithapur <getuser@tatachemicals.com> wrote:
> Hi there,
>
> I need some help in understanding a few things
> related with piping analysis.
> If anyone could provide information as to where i
> could get guidance
> material with regards to the moment calculation in
> pipe stress analysis.
> Solved examples would be even better.
> I have a problem in understanding how the moment is
> calculated for a
> piping layout. I have gone through the ASME B31.3,
> Pipe Stress Analysis by
> SAM KANAPPAN, but still am not clear as to how the
> moments are calculated.
>
> Regards Deepak.
>
> > -----Original Message-----
> > From: Steve McKenzie [SMTP:mechproj@xtra.co.nz]
> > Sent: Saturday, July 17, 2004 1:01 PM
> > To: <a href="/group/PipingDesign/post?postID=pKSqJIN6aoFjj34InlTbqdFHdw7M4dWbs-PBmonGjA7wyZ3sT8QnUtpZbhWY3FgpxsVN3HDk6jf0vYcGlzm6SoAzAT9txFY">PipingDesign@yahoogroups.com</a>
> > Subject: RE: [PipingDesign] When Flexibility
> Analysis is Needed?
> >
> >
> > Have a look at Kellog "Design of Piping Systems"
> section 4.2
> > "Preliminary Segregation of Lines With Adequate
> Flexibility". It is
> > necessary to read the description so I have not
> copied the "Formula"
> > Also look at ANSI/ASME B31.1 1986 clause 119.7
> "Analysis". Also note the
> > disclaimers.
> >
> > Cheers
> >
> > Steve
> >
> >
> > -----Original Message-----
> > From: <a href="/group/PipingDesign/post?postID=UiFK4veaVIipgP6Zs0fA7zi3_N3jT2_eB6Mpt7LkiKXg8vGi5jgeErNiZy1VS1t8Azr973J9vtLwrCEJmIo">conor.walshe@alcan.com</a>
> [mailto:conor.walshe@alcan.com]
> > Sent: Saturday, July 17, 2004 3:01 PM
> > To: <a href="/group/PipingDesign/post?postID=pKSqJIN6aoFjj34InlTbqdFHdw7M4dWbs-PBmonGjA7wyZ3sT8QnUtpZbhWY3FgpxsVN3HDk6jf0vYcGlzm6SoAzAT9txFY">PipingDesign@yahoogroups.com</a>
> > Subject: Re: [PipingDesign] When Flexibility
> Analysis is Needed?
> >
> >
> > This question has been asked by probably every
> person starting in this
> > field over the years. Even the experts have no
> conclusive formulae or
> > critieria. The reason being is that every piping
> system is different
> > (bar
> > duplicate systems). Large Engineering consultants
> general produce
> > guidelines for the selection of piping that
> requires pipe stress
> > analysis,
> > but at the end of the day it is up to the Pipe
> Stress Analyst.
> >
> > Do a search for the Norsok standard on the web, a
> good starting point.
> > But
> > experience and understanding of pipings systems
> will refine your skills
> > over the years.
> >
> > Conor Walshe
> > Mechanical Design Engineer
> > Alcan Engineering Australia Pty Limited
> > A member of the Alcan Group of companies
> > Tel: (07) 3218 3648
> > Fax: (07) 3236 0155
> > e-mail: <a href="/group/PipingDesign/post?postID=UiFK4veaVIipgP6Zs0fA7zi3_N3jT2_eB6Mpt7LkiKXg8vGi5jgeErNiZy1VS1t8Azr973J9vtLwrCEJmIo">conor.walshe@alcan.com</a>
> >
> >
> >
> >
> >
> > GET Mithapur <getuser@tatachemicals.com>
> > 16/07/2004 09:01 PM
> > Please respond to
> > <a href="/group/PipingDesign/post?postID=pKSqJIN6aoFjj34InlTbqdFHdw7M4dWbs-PBmonGjA7wyZ3sT8QnUtpZbhWY3FgpxsVN3HDk6jf0vYcGlzm6SoAzAT9txFY">PipingDesign@yahoogroups.com</a>
> >
> >
> > To
> > "'pipingdesign@yahoogroups.com'"
> <pipingdesign@yahoogroups.com> cc
> >
> > Subject
> > [PipingDesign] When Flexibility Analysis is
> Needed?
> >
> >
> >
> >
> >
> >
> > Dear All,
> >
> > Can anybody tell us when Piping Flexibility
> Analysis is needed? I have
> > referred B.31.3 & B31.1 (clause 319.4.1 & 119.7.1)
> but not reached any
> > clear conclusion.
> >
> > What are criteria involved for Piping Stress
> Analysis.
> > Are there any minimum requirements to be
> considered while deciding for
> > Flexibility Analysis?
> >
> > DEEPAK
> >
> >
> >
> >
> > =========================================
> > PipingOffice - Excel Spreadsheets for Piping
> Calculations
> > <a href="http://www.pipingoffice.us/">http://www.pipingoffice.us/</a>
> =========================================
> > Main site: <a href="http://www.pipingdesign.com">http://www.pipingdesign.com</a>
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> >
> >
> > Notice:
> > This message and any attachments are the property
> of Alcan and are
> > intended solely for the named recipients or entity
> to whom this message
> > is
> > addressed. If you have received this message in
> error please inform the
> > sender via e-mail and destroy the message. If you
> are not the intended
> > recipient you are not allowed to use, copy or
> disclose the contents or
> > attachments in whole or in part.
> >
> > [Non-text portions of this message have been
> removed]
> >
> >
> >
> >
> > =========================================
> > PipingOffice - Excel Spreadsheets for Piping
> Calculations
> > <a href="http://www.pipingoffice.us/">http://www.pipingoffice.us/</a>
> =========================================
> > Main site: <a href="http://www.pipingdesign.com">http://www.pipingdesign.com</a>
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> >
> >
> > =========================================
> > PipingOffice - Excel Spreadsheets for Piping
> Calculations
> > <a href="http://www.pipingoffice.us/">http://www.pipingoffice.us/</a>
> > =========================================
> > Main site: <a href="http://www.pipingdesign.com">http://www.pipingdesign.com</a>
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
>
Do you Yahoo!?
Vote for the stars of Yahoo!'s next ad campaign!
<a href="
http://advision.webevents.yahoo.com/yahoo/votelifeengine/">
http://advision.webevents.yahoo.com/yahoo/votelifeengine/</a>
Received on Sun Jul 18 05:40:00 2004