Re: Dimensioned Isometrics

From: <Dacharaju>
Date: Wed Apr 13 2005 - 23:53:00 EDT

Mr Paul,
I agree with you that isos are made to fit to field.I was talking about about "Field Welds Location" verification by Field staff and not dimensions.

With best regards,

D.K.M.Rao.

Paul Bowers <pbowers@pipingdesign.com> 04/14/2005 02:14 AM
Please respond to
<a href="/group/PipingDesign/post?postID=YDvHXcKip6rqTri09JxoHncIZJh75TQp_S26LOwF5F3uS58qVZCcZHyATHRAX-VcY6nc_V3S8RrvRHg0Edi9QJsvrUOD92Y">PipingDesign@yahoogroups.com</a>

To
<a href="/group/PipingDesign/post?postID=YDvHXcKip6rqTri09JxoHncIZJh75TQp_S26LOwF5F3uS58qVZCcZHyATHRAX-VcY6nc_V3S8RrvRHg0Edi9QJsvrUOD92Y">PipingDesign@yahoogroups.com</a> cc

Subject
Re: [PipingDesign] Dimensioned Isometrics

Dacharaju Krishnamohan Rao wrote:

> In addition to the information as indicated by Mr Adolphus, the FIELD
WELD
> locations are also shown by some of the consultants in Engineering phase

> which are usually verified (changed if required) by the field peronnel.

No way. All piping isos are perfect and fit exactly in the field as drawn. Seriously, though...

Also, mark numbers for individual spools, field trim allowance, correct valve handwheel orientation, correct pressure seal direction for valve seats, high point vents and low point drains, consistent north arrow, heat tracing, notes relating to instrumentation design standards, orientation for HP/LP connections on orifice plate installations, flow direction, X-Y reference to a nearby structural column, instrumentation bubbles, related P&ID/model/piping GA reference, control valve default state, etc.

Paul

---

PipingOffice - Excel Spreadsheets for Piping Calculations <a href="http://www.pipingoffice.us/">http://www.pipingoffice.us/</a>

---

Main site: <a href="http://www.pipingdesign.com">http://www.pipingdesign.com</a>

Yahoo! Groups Links
To visit your group on the web, go to:
<a href="http://groups.yahoo.com/group/PipingDesign/">http://groups.yahoo.com/group/PipingDesign/</a>

To unsubscribe from this group, send an email to: <a href="/group/PipingDesign/post?postID=IvuWwec964bbFpcaQ6dMQLGG3Up9gsLCwxZLmKJGFH7lvafdZBWbyNqneAvMeRK_xg8MXlgChbbWEJcwRzPacij0YHwHoOMoXEv8-qWvmKD2UA">PipingDesign-unsubscribe@yahoogroups.com</a>

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

--------------------------------------------------------------------------------\
------------------

Confidentiality Notice : This e-mail and any attachments are confidential to the addressee and may also be privileged. If you are not the addressee of this e-mail, you may not copy, forward, disclose or otherwise use it in any way whatsoever. If you have received this e-mail by mistake, please e-mail the sender by replying to this message, and delete the original and any print out thereof.

[Non-text portions of this message have been removed] Received on Wed Apr 13 23:53:00 2005