RE: Just a joke.

From: <Mchugh@technip.com>
Date: Tue Jul 05 2005 - 06:56:00 EDT


Seems so... but this is how I got it.

Mukesh Chugh,
Principal Engineer - Piping,
Technip KT India Ltd.
0120-5301259 (Direct) 

              Shamrose Chaudhry
              <schaudhry@descon
              .com.pk>                                                   To
              Sent by:                  <a href="/group/PipingDesign/post?postID=7OrNvtpQC4qWF4biERycolZmv1TMhxKPv7PqvFxMv243vgqOLur-Pd-OZqPdMTFTZ0C6drpNd7vdoJ-jT4pLCkzooEg9og">PipingDesign@yahoogroups.com</a>
              PipingDesign@yaho                                          cc
              ogroups.com
                                                                    Subject
                                        RE: [PipingDesign] Just a joke.
              07/05/2005 03:40
              PM


              Please respond to
              PipingDesign@yaho
                 ogroups.com

Great one.. But looks incomplete at end... isn't it.

Regards,

-----Original Message-----
From: <a href="/group/PipingDesign/post?postID=7OrNvtpQC4qWF4biERycolZmv1TMhxKPv7PqvFxMv243vgqOLur-Pd-OZqPdMTFTZ0C6drpNd7vdoJ-jT4pLCkzooEg9og">PipingDesign@yahoogroups.com</a> [mailto:<a href="/group/PipingDesign/post?postID=7OrNvtpQC4qWF4biERycolZmv1TMhxKPv7PqvFxMv243vgqOLur-Pd-OZqPdMTFTZ0C6drpNd7vdoJ-jT4pLCkzooEg9og">PipingDesign@yahoogroups.com</a>] On Behalf Of <a href="/group/PipingDesign/post?postID=QmFXq8RBDDvgZXbVzJLSdWXdiwcPUOkvy1BDNVxHMOe3N_6zWwTGMDGw7gZmn9vyxOZJ_uPnVDiM9Bqp">Mchugh@technip.com</a> Sent: Tuesday, July 05, 2005 1:45 PM
To: <a href="/group/PipingDesign/post?postID=7OrNvtpQC4qWF4biERycolZmv1TMhxKPv7PqvFxMv243vgqOLur-Pd-OZqPdMTFTZ0C6drpNd7vdoJ-jT4pLCkzooEg9og">PipingDesign@yahoogroups.com</a> Subject: [PipingDesign] Just a joke.

READ THE SPECS... Mr. Santa Singh is a brilliant engineer from Patiala College of Engineering and Mr. Banta Singh is his boss, a gold-medallist from Jalandhar University. Both of them are serving for Punjab Pipes whose owner is Ms. Gurujit Kaur.

In one of the tenders Mr. Santa Singh has declared the pipe specs.

Prepared by: SANTA SINGH
Approved by: BANTA SINGH

  1. All pipe is to be made of a long hole surrounded by metal or plastic, centered around the hole.
  2. All pipe is to be hollow throughout the entire length - do not use holes whose length is different length from the pipe.
  3. The ID (Inside Diameter of all pipe must not exceed the OD (Outside Diameter) - otherwise the hole will be on the outside.
  4. All pipe is to be supplied with nothing in the hole, so that water, steam or other stuff can be put inside at a later date.
  5. All pipe should be supplied without rust; this can be more readily applied at the job site. NOTE: Some vendors are now able to supply pre-rusted pipes. If available in your area, this product is recommended, as it will save a great deal of time at the job site.
  6. All pipe over 500ft (150m) in length should have the words "LONG PIPE" clearly painted on each side at the end, so that the contractor knows it's a long pipe.
  7. Pipe over 2 miles (3.2km) in length must also have the words "LONG PIPE" painted in the middle, so the contractor will not have to walk the entire length of the pipe to determine whether or not it is a long pipe or a short pipe.
  8. All pipe over 6ft (1.83m) in diameter must have the words "LARGE PIPE" painted on it, so the contractor will not mistake it for small pipe.
  9. Flanges must be used on all pipe. Flanges must have holes for bolts, quite separate from the big hole in the middle.
  10. When ordering 90 or 30-degree elbows, be sure to specify left-hand or right-hand, otherwise you will end up going the wrong way.
  11. Be sure to specify to your vendor whether you want level, uphill or downhill pipe. If you use downhill pipes for going uphill, the water will flow the wrong way.
  12. All couplings should have either right-hand or left-hand threads, but do not mix the threads, otherwise as the coupling is being screwed on one pipe, it is being unscrewed from the other.
  13. All pipes shorter than 1/8in (3mm) are very uneconomical in use, requiring many joints. They are generally known as washers.
  14. Joints in pipes for piping water must be watertight. Those in pipes for compressed air, however, need only be airtight.
  15. Lengths of pipes may be welded or soldered together. This method is not recommended for concrete or earthenware pipes.
  16. Other commodities are often confused with pipes. These include: conduit

PipingOffice - Excel Spreadsheets for Piping Calculations <a href="http://www.pipingoffice.us/">http://www.pipingoffice.us/</a>

Main site: <a href="http://www.pipingdesign.com">http://www.pipingdesign.com</a>

Yahoo! Groups Links

Disclaimer:
This e-mail message and information contained in or attached to this message is privileged, confidential, and protected from disclosure and is intended only for the person or entity to which it is addressed. Any review, re-transmission, dissemination, printing or other use of, or taking of any action in reliance upon this information by persons or entities other than the intended recipient is prohibited. If you receive this message in error, please immediately inform the sender by reply e-mail and delete the message and any attachments. Please note that e-mails are susceptible to change. DESCON Engineering shall not be liable for the improper or incomplete transmission of the information contained in this communication nor for any delay in its receipt or damage to your system. DESCON Engineering does not guarantee that the integrity of this communication has been maintained or that this communication is free of viruses, interceptions or interference.


PipingOffice - Excel Spreadsheets for Piping Calculations <a href="http://www.pipingoffice.us/">http://www.pipingoffice.us/</a>

Main site: <a href="http://www.pipingdesign.com">http://www.pipingdesign.com</a>

Yahoo! Groups Links Received on Tue Jul 05 06:56:00 2005

This archive was generated by hypermail 2.1.8 : Tue Mar 04 2008 - 11:40:42 EST