To all,
Our firm Avineon, works in all of the major platforms, PDS, PDMS, Rebis, Catia
etc. We provide customization to 3D modelling to ISO creation to BOM/MTO etc. We
not only have offices worldwide we also offer these services in a low cost high
quality center out of India. We have the ability to supply any size company with
staff augmentation to project services to conversion of their 2D drawings into a
3D model. In all the disciplines as well as Instrumentation, structural,
electrical etc. We work on Power, Process, Offshore etc. If you all need
additional design or engineering support by all means call or email us at:
ymolner@avineon.com or 772 873 4072.
Regards;
Yancey
Paul Bowers <pbowers@pipingdesign.com> wrote:Thanks for the input, CV, great
comments. PDS and PDMS are the Ferraris of
plant design, and from what I've heard, those that use them would never even
consider an AutoCAD-based solution.
But companies that cannot afford the large up-front purchase/rental and maintenance (I.E., specialized support personnel) costs of these programs are not likely to use them. They are just too complicated and expensive to acquire. These are programs for "the big boys" only, the companies that can afford to spend the bucks.
ACAD-based solutions, on the other hand, are quite comparatively affordable and there is a huge user base out there (PDS/PDMS is pretty much a closed shop). Even the lowest level Pentium4 or AMD Athlon chip with enough inexpensive RAM and a decent graphics card can now run AutoCAD in 3D quite easily. Yes, I know that AutoCAD and MS Windows have their limitations.
In particular, I'm thinking about smaller consulting firms that bid on projects (or upgrades to existing facilities) but are shut out because of "incompatible software".
Paul
Sent: Friday, November 15, 2002 8:26 PM
Subject: Re: [PipingDesign] 3D CAD Equipment Models
> Dear Paul,
> I have over 34 years of experience and am attached to
> a detailed plant model engineering consultancy
> organization catering to the hydrocarbon sector
> (essentially refineries). We are in the business of
> designing 3D plant models and extract all the required
> working deliverables, like GADs, isometrics and MTOs
> in 2D formats. During the last 7 years we have
> executed more than a dozen processing plants through
> this route. Our system is Intergraph's PDS (Plant
> Design System). Here, the piping engineering
> department, to which I belong, caters to almost all
> the 3D modelling activities, starting from the
> foundations, underground piping and equipments to the
> above ground piping and on-line instruments, including
> pipe supports. Our clients are quite happy with the
> outcome and the result is that we are loaded with jobs
> slightly beyond our dispensing capabilities.
> PDS supports all the needs to a great extent.
> regarding off-spec items, a thorough customization
> exercise has to be taken up in the beginning. Then the
> database takes care of the items and all get accounted
> for in the final download of material take off. Our
> judgement is that this system is adequate for our
> needs. It need a responsible person to do the
> administration of the project in the PDS set-up.
> There is equally powerfull software called PDMS
> serviced by CADCENTRE also available in the market. We
> had done some evaluation of this software as well.
> To begin with, we had Autoplant, which was
> subsequently discarded due to various reasons. It is
> rather difficult for Autoplant (Rebis) to support a
> very large database which a plant demands.
> Please give a thought to what I have mentioned and
> decide your course of action. Lining up a third party
> to do the detailing work needs a dynamic connectivity
> (leased line) of the central database at the home
> office as well as at the agency's office. Often this
> may end up in sharing the intellectual property.
> Handling the revisions in due course of engineering
> also needs attention.
> --- Paul Bowers
wrote:
> > Is anyone aware of a third party company that
> > creates and sells 3D models of
> > process equipment?
> >
> > I've only worked with Rebis, which has a package
> > option with which designers
> > can customize various parameters of common equipment
> > (centrifugal pumps,
> > tanks, towers/reboilers, etc.) to create a model
> > that can be inserted into
> > the overall model. The piping connections have
> > "connectivity" built-in, so
> > that the finished model "knows" the spec of the
> > connection and when running
> > piping up to the nozzle, it auto-connects and
> > returns an error message if
> > the pipe spec doesn't match with the equipment spec.
> > This is fine for the
> > more common pieces one sees in process plants, but
> > equipment used in pulp
> > and paper or mining operations (for example) don't
> > fit into the available,
> > customizeable components. This means that these
> > elements have to be created
> > in straight 3D AutoCAD by a fairly proficient
> > modeller - who may or may not
> > be a piping/mechanical person - and the end result
> > has no "connectivity".
> >
> > It would seem to be worthwhile for equipment
> > manufacturers to provide these
> > models themselves, but maybe it's seen as not being
> > cost-effective. After
> > all, a process engineer is not going to spec a piece
> > of equipment purely
> > based on whether it has a CAD model available. And
> > for a third-party company
> > to expend the time, effort and money also seems to
> > be a non-starter, as such
> > models would likely be easily copied without having
> > to pay the developer.
> >
> > Any thoughts?
Discussion List sponsor: Texas Flange - a good source for information on
industrial flanges, all they ask is for referrals for designs they help with.
877-610-8924.
www.texasflange.com
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
[Non-text portions of this message have been removed] Received on Sun Nov 17 21:47:00 2002
This archive was generated by hypermail 2.1.8 : Mon Oct 27 2008 - 20:23:58 EDT